|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
2.8V LVCMOS Surface Mount Crystal Clock Oscillator 5216 XO 2111 Comprehensive Drive 2111 Comprehensive Drive Aurora, Illinois 60505 Aurora, Illinois 60505 Phone: 630- 851- 4722 Phone: 630- 851- 4722 Fax: 630- 851- 5040 Fax: 630- 851- 5040 www.conwin.com www.conwin.com Features: 1.8 to 80 MHz 2.8V Operation RoHS Compliant Tri-State Enable / Disable Function Overall Frequency Tolerance: 5216 25 ppm, 5226 50 ppm, 5236 100 ppm Temperature Range: -40 to 85C Power Saving Stand-By Current Ceramic Surface Mount Package Tape and Reel Packaging US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 The Connor-Winfield models 5216, 5226, and 5236 are 7.5mm x 5mm, 2.8V LVCMOS, Surface Mount, Fixed Frequency Crystal Oscillators (XO) designed for use in all applications requiring precision clocks. This oscillator features low stand-by current (10uA) when the output is disabled. The RoHS compliant, surface mount package is designed for high-density mounting and is optimum for mass production. Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Minimum -55 -0.5 Nominal Maximum 125 7.0 Units C Vdc Notes Operating Specifications Parameter Frequency Range (Fo) Frequency Tolerance 5216 5226 5236 Operating Temp Range Supply Voltage (Vdd) Supply Current (Icc) 1.8 to 31.999 MHz 32 to 50 MHz Minimum 1.8 -25 -50 -100 -40 2.66 Nominal Maximum 80 25 50 100 85 2.94 12 20 Units MHz ppm Notes 1 2.8 - C Vdc mA Input Characteristics Parameter Enable Voltage - (Vih) Disable Voltage - (Vil) Enable Time Disable Time Output Disable Current (lcc) Minimum 70% Vdd Nominal Maximum 30% Vdd 10 150 10 Units Vdc Vdc nS nS uA Notes 2 HCMOS Output Characteristics Parameter Load (Voh) Voltage High (Vol) Low (loh) Current High (lol) Low Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Start-Up Time Jitter Notes: 1. Inclusive of calibration @ 25C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging. 2. Oscillator requires a pull up resistor from pin 1 to Vcc to insure proper operation. Specifications subject to change without notice. All dimensions in inches. (c) Copyright 1998 The Connor-Winfield Corporation Bulletin Page Revision Date Sm074 1 of 2 01 01 April 2002 Minimum 2.39 -4 45 - Nominal 50 - Maximum 15 0.29 4 55 5 10 5 Units pF Vdc mA % nS mS pS RMS Notes 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Package Characteristics Package Hermetically sealed ceramic package and metal cover Suggested Pad Layout Environmental Characteristics Temperature Cycle The specimen shall meet electrical characteristics after tested 5 cycles of -55C / 30 minutes and +125C / 30 minutes Hermetical No bubbles appear in Flourinert (FC-43) at 125C 5C for 5 minutes Solvent Resistance Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene Soldering General Conditions 260C max x 10 sec max x 2 times max or 230C max x 180 sec max x 1 time Typical Operation Data (Vapor phase reflow) 20 to 100 sec up to 215C, 50 sec at 215C, then down to room temperature per 1 to 5C / sec Bypass capacitor, C-by, should be ceramic capacitor .01 uf Test Circuit OSCILLOSCOPE PROBE Mechanical Characteristics The specimen shall meet electrical characteristics after tested 3 times, Free Drop testing on the hard wooden board from a height of 75 cm. Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, 55-2000 Hz 20 G's, 2 hours for each plane Thermal Shock After applied Thermal Shock of 260C max x 10 sec max x 2 times, or 230C max x 180 sec max, the specimen shall meet electrical characteristics Solderability (EIAJ-RCX-0102.101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235C 5C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec 0.5 sec into solder bath After performing the above procedures, a newly soldered coverage shall be greater than 90% POWER SUPPLY Free Drop OSC FREQ COUNTER INPUT FOR E/D Output Waveform SYMMETRY Pin Connections 1: Enable/Disable 2: Ground 3: Output 4: Vcc Tape and Reel Dimensions Ordering Information 5216 CLOCK SERIES - 80.00 MHz CENTER FREQUENCY Dimensional Tolerance: .02" (.508mm) .005"(.127mm) Bulletin Page Meets EIA-481A and EIAJ-1009B 2,000 PCS/Reel Specifications subject to change without notice. All dimensions in inches. (c) Copyright 1998 The Connor-Winfield Corporation Revision Date Sm074 2 of 2 01 01 April 2002 |
Price & Availability of 5216 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |